SP-6000.1D - @2 ohm

قیمت فروش€673,00 قیمت معمولی€1.346,00
ذخیره €673,00
✅
ReadyShips in 24/48 h from Italy

Pay in easy, interest-free installments with Klarna.


 

SP Audio - Super Power AudioSUPER POWER AUDIO
DESIGNED IN ITALY
MMXXVI
1 channel · class D · monoblock

6000 watt RMS.
into 2 ohm.

One channel, one subwoofer, all the current the car can give. Class D monoblock with forced cooling, variable filters and full protection — built for systems where the limiting factor is no longer the amplifier, but the electrical system behind it.

SP-6000.1D class D monoblock amplifier at 2 ohm, 307 x 219 x 74 mm, power and speaker terminals

6000WRMS · 2 Ω MONO
3000WRMS · 4 Ω MONO
1600WRMS · 8 Ω MONO
🔒 Secure checkout · SSL & PCI DSS↩ 14 days to change your mind (EU)✓ Invoice from an Italian company
✓ ITALIAN DESIGN✓ CLASS D MONOBLOCK✓ FORCED COOLING✓ FULL PROTECTION✓ FREE SUPPORT
01

Power, measured not promised

MONO · 8 Ω
1600 W
MONO · 4 Ω
3000 W
MONO · 2 Ω
6000 W

RMS @ 14.4 V · CONTINUOUS POWER, NOT BURST · MINIMUM LOAD 2 Ω

02

Why this amplifier

All the current on one channel

A single class D output stage delivers 6000 W RMS into 2 ohm: no bridging, no power split between two channels. Everything goes to the subwoofer.

Forced cooling, not just fins

Smart cooling system with a temperature-driven fan on top of the finned chassis. The fan only spins when the amplifier asks for it, and the output stage keeps working when the music does not stop.

Two power input blocks

The power panel carries two GND / REM / +12 V terminal blocks, one on each side, so the current arrives on two runs instead of one and the connection stays cool under load.

Protected, not fragile

Protection against output short circuit, high supply voltage, low supply voltage and overheating. It works from 9 V to 16 V, so a starting dip does not become a repair.

“Continuous RMS only. No peak, no burst, no marketing watts.”
03

Connections and controls

SP-6000.1D: control panel with bass boost, gain, crossover and RCA in/out, and power panel with two GND / REM / +12 V terminal blocks
SP-6000.1D seen from the control side: RCA inputs, crossover knobs and heat-dissipating chassis
Free shippingDispatched from Italy in 24–48 working hoursWarranty on manufacturing defectsFree technical support from Italy
USER MANUAL · PDF

Wiring, loads and impedance, filters and gain calibration.

⇩  Download the manual (PDF)
04

What you receive

Amplifier first, installation material second.

The SP-6000.1D arrives ready to be mounted: chassis with four fixing feet, direct-insert screw terminals and the complete control panel. Everything that goes around it — cable, fuse, ground, distribution — is chosen on the car, not on the amplifier.

In the box: amplifier · user manual (PDF above) · protective packaging.
Not included: power and speaker cable, inline fuse holder, RCA cable, distribution block and remote level control — installation material, chosen for your vehicle.

SP-6000.1D class D monoblock amplifier seen from above, grille and finned chassis
05

Technical specifications

POWER PER CHANNEL — RMS @ 14.4 V
Mono 2 ohm 6000 W
Mono 4 ohm 3000 W
Mono 8 ohm 1600 W
Minimum load 2 ohm
Topology Class D, mono, 1 channel
POWER SUPPLY & PROTECTION
Supply voltage 9 V – 16 V (12 V negative ground)
Remote turn-on +12 V
Power input terminals 2 × GND / REM / +12 V
Thermal management Smart cooling system, temperature-driven fan
Protections Output short circuit, high voltage, low voltage, thermal
FILTERS & INPUTS
Low-pass filter (LPF) 80 Hz – 10 kHz, variable
High-pass filter (HPF) 15 Hz – 80 Hz, variable
Bass boost 0 – 12 dB at 50 Hz, variable
Frequency response 10 Hz – 20 kHz (3 dB)
S/N ratio 100 dB
Input sensitivity 200 mV
Input impedance 56 kΩ
Inputs / outputs RCA input · RCA output · remote level control port
DIMENSIONS
Dimensions L × W × H 307 × 219 × 74 mm
Sold as Unit
SP-6000.1D dimensioned drawing: 307 x 219 x 74 mm

MANUFACTURER’S LABORATORY DATA · PEAK OR “BURST” FIGURES USED IN SOME MARKETS ARE NOT RMS AND ARE NOT LISTED

06

Complete the system

07

Before you install it

  • Cable section and fuse come first. On an amplifier of this class the run from the battery is normally 0 AWG, with a main fuse within 20 cm of the battery sized to the cable. An undersized cable is the most common cause of voltage drop and disappointing bass.
  • Ground on clean metal, short. Scrape the paint off, use the same section as the positive and keep the ground lead as short as you can. Most “noise problems” are ground problems.
  • Leave the fan and the fins free. The amplifier cools itself with a temperature-driven fan and a finned chassis: never cover it with carpet, luggage or foam, and leave air around it.
  • Set the gain last, and set it as a match, not a volume. Bass boost at 0, source at about three quarters, then raise the gain until it is loud and clean, and stop there. The supply must stay between 9 V and 16 V while it plays.
08

Questions installers ask

Which subwoofer impedance should I use?Any load down to 2 ohm: 2 ohm = 6000 W RMS · 4 ohm = 3000 W RMS · 8 ohm = 1600 W RMS. Below 2 ohm the protection steps in and, if it is repeated, the output stage is damaged.
Do I need to upgrade the battery and the alternator?The data sheet gives the supply range (9 V – 16 V), not the current draw. On this power class, plan the electrical system first: cable section, main fuse, a clean ground and a battery and alternator that keep the voltage up while the amplifier plays.
Which filters does it have?Low-pass 80 Hz – 10 kHz, high-pass 15 Hz – 80 Hz and bass boost 0 – 12 dB centred on 50 Hz, all variable on the panel, plus the gain.
Can I connect a second amplifier to it?Yes: the panel has an RCA output next to the RCA input, so the signal can be passed on to another amplifier without a splitter.
What are the dimensions?307 × 219 × 74 mm, with four fixing feet. It has two GND / REM / +12 V terminal blocks, one on each side of the power input panel.
Free technical support from Italy. Write or call and a person answers, with the real data of the product sheets. Tell us what you want to build — impedance, power, box litres, crossover points — and we will help you match it.
spaudio@spaudio.it · +39 340 807 8778

Accepted payment methods
Visa · Mastercard · Maestro · American Express · PayPal · Apple Pay · Google Pay · Shop Pay · Klarna

SP Audio — Super Power Audio. Designed in Italy by Audiocar Import & Export SRLS, Milano, official SP Audio distributor for Europe.