SP 12MM Midrange Extreme 12" 500W RMS

Sale price€175,00 Regular price€350,00
Save €175,00
5.0
✅
ReadyShips in 24/48 h from Italy

Free shipping worldwide. Pay in easy, interest-free installments with Klarna.


SP Audio - Super Power AudioSUPER POWER AUDIO
DESIGNED IN ITALY
MMXXVI
midrange extreme · ferrite · 12 inch

101.5 dB.
Twelve inches of midbass.

A 12" midrange built for level: 500 W RMS, 101.5 dB, a 76.2 mm (3") CCAW voice coil and an 85 Oz ferrite motor behind 530 cm² of cone. 45 Hz to 6 kHz — low enough to carry the midbass, so the subwoofer only has to do the bass. Unit price.

Two SP 12MM 12 inch midrange extreme speakers in an urban street setting

500WRMS · 4 Ω
1000WMAX · PEAK
101.5dBSPL 1W/1M
🔒 Secure checkout · SSL & PCI DSS↩ 14 days to change your mind (EU)✓ Invoice from an Italian company✓ Data from the 2026 factory manual
✓ ITALIAN DESIGN✓ 4 OHM✓ UNIT PRICE✓ FREE SUPPORT✓ FERRITE MOTOR
01

Power, measured not promised

RMS · 4 Ω
500 W
MAX · PEAK
1000 W

PER SPEAKER · RMS IS CONTINUOUS POWER, NOT BURST · NOMINAL 4 Ω

02

Why this midrange

101.5 dB from 530 cm² of cone

Sensitivity comes from area and motor, not from watts. 530 cm² of Sd and a Bl of 11.848 TM: one watt in, 101.5 dB out.

500 W RMS on a 3" coil

76.2 mm of CCAW voice coil: the thermal reserve that lets it take 500 W of continuous work, not a burst rating.

Down to 45 Hz

It reaches 45 Hz, so it carries the midbass — kick, bass guitar, the punch you feel in the chest — and leaves only the low bass to the subwoofer.

85 Oz ferrite, built to last

A big ferrite ring and a curvilinear fiberglass reinforced paper cone: no exotic materials to fail, just the mass and the stiffness the job needs.

“Continuous RMS only. No peak, no burst, no marketing watts.”
03

Look at it closely

SP 12MM front view: cone, orange-rimmed surround and aluminium phase plug
01 · the coneCurvilinear profile, fiberglass reinforced paper, M-ROLL polycotton surround, solid aluminium phase plug in the centre.
SP 12MM midrange pair in a city alley against a brick wall
02 · the motor85 Oz ferrite magnet, 76.2 mm CCAW voice coil, Bl 11.848 TM.
Free shippingDispatched from Italy in 24–48 working hoursWarranty on manufacturing defectsFree technical support from Italy
FACTORY MANUAL & SPECIFICATION SHEET

Full specifications, Thiele-Small parameters and mounting data, straight from the 2026 factory sheet.

⇩ Open the manual (PDF)

English · 2026 edition · opens in a new tab

04

What you receive

One speaker, sold singly.

The price on this page is for one SP 12MM. SPL builds use them in twos and fours: order the number your project needs, they ship from the same production batch. Packed in the SP Audio box with the protective foam.

In the box: 1 × SP 12MM midrange · mounting screws · SP Audio packaging.
Not included: grilles, speaker cable, crossovers and adapter rings — installation materials, chosen for your car.

SP 12MM 12 inch midrange held by hand in a city alley
05

Technical specifications

POWER & LOAD
Rated power (RMS) 500 W
Peak power (MAX) 1000 W
Rated impedance 4 ohm
ACOUSTIC
Nominal diameter 300 mm (12")
Sensitivity 101.5 dB SPL 1W/1M
Frequency range 45 Hz - 6 kHz
MOTOR & MATERIALS
Voice coil diameter 76.2 mm / 3" CCAW
Winding material Copper clad aluminium wire (CCAW)
Magnet 85 Oz ferrite
Phase plug Aluminium, solid
Suspension M-ROLL, polycotton
Cone Curvilinear, fiberglass reinforced paper
MOUNTING
Outer diameter 310.5 mm (12.2")
Cut-out diameter 282.5 mm (11.1")
Sold as Unit (1 piece)
THIELE-SMALL PARAMETERS
Fs 88 Hz
Re 3.7 ohm
Qts 0.577
Qes 0.631
Qms 6.740
Vas 30 L
Xmax 1.5 mm
Sd 530 cm²
Cms 75.2 µm/N
Mms 43.082 g
Bl 11.848 TM
η0 3.19 %

MANUFACTURER’S LABORATORY DATA · PEAK OR “BURST” FIGURES USED IN SOME MARKETS ARE NOT RMS AND ARE NOT LISTED

06

Complete the system

07

Before you install it

  • Do not go below 4 ohm per channel. Two speakers in parallel on one channel give 2 ohm: most amplifiers will heat up or go into protection.
  • Use a high-pass filter. This is a midrange, not a subwoofer: cut below 45 Hz and let the sub do the low bass. Xmax is 1.5 mm — it is built for level, not for excursion.
  • Bring the tweeter in below 6 kHz. The cone stops at 6 kHz, so the top end has to be covered by a tweeter, low-passed and high-passed to meet it.
  • Check the numbers first. Cut-out 282.5 mm, outer 310.5 mm: a 12" midrange wants a custom baffle or a door pod, solidly fixed. Measure the depth available in your panel before you cut.
08

Questions installers ask

How much power does the SP 12MM handle?500 W RMS continuous and 1000 W peak. The price on this page is for one speaker.
What amplifier does it need?4 ohm nominal: an amplifier able to deliver about 500 W RMS at 4 ohm on the channel that drives it.
What is the difference with the SP 12MM NEO?Same 12" cone and the same 500 W RMS. The NEO uses a neodymium magnet, so the motor is much smaller and lighter; this one uses an 85 Oz ferrite magnet.
What hole do I need to cut?282.5 mm (11.1"), with a 310.5 mm (12.2") outer diameter.
Where do I cross it?High-pass at 45 Hz or above. It runs to 6 kHz, so the tweeter has to come in by then.
Free technical support from Italy. Write or call and a person answers, with the real data of the product sheets. Tell us what you want to build — power, crossover points, door or kick panel — and we will help you match it.
spaudio@spaudio.it · +39 340 807 8778

Accepted payment methods
Visa · Mastercard · Maestro · American Express · PayPal · Apple Pay · Google Pay · Shop Pay · Klarna

SP Audio — Super Power Audio. Designed in Italy by Audiocar Import & Export SRLS, Milano, official SP Audio distributor for Europe.