SP TW 28 Bullet Tweeter 100W RMS (Pair)
Free shipping worldwide. Pay in easy, interest-free installments with Klarna.
SUPER POWER AUDIODESIGNED IN ITALY
MMXXVI
110 dB.
Highs you hear over the engine.
A bullet tweeter built for SPL: 1" throat, 32.4 mm voice coil, 8 Oz magnet, 150 W RMS. At 110 dB it cuts through a loud system without being pushed. 95 mm across, 47 mm deep. Sold as a pair.
Power, measured not promised
PER TWEETER · RMS IS CONTINUOUS POWER, NOT BURST · 4 Ω NOMINAL · ALWAYS DRIVEN THROUGH A CROSSOVER
Why this tweeter
A bullet is a horn: the throat concentrates the energy instead of spreading it. At 110 dB it needs a fraction of the power a dome needs for the same level.
1.27" / 32.4 mm wound with CCAW aluminium wire. A big coil is why this one takes 150 W RMS and keeps going.
The motor is what turns watts into movement. Eight ounces on a tweeter this size means control, not just loudness.
95 mm across, 47 mm deep, half a kilo. It goes on the A-pillar, on the dash or on a kick panel, aimed where you want it.
Look at it closely
Full specifications and mounting data, straight from the 2026 factory sheet.
⇩ Open the manual (PDF)English · 2026 edition · opens in a new tab
What you receive
The price on this page is for a pair: left and right, from the same production batch, so the two sides of the car match. Packed in the SP Audio box.
In the box: 2 × SP TW 28 bullet tweeter · SP Audio packaging.
Not included: crossovers or series capacitors, speaker cable and mounting hardware for your car — a tweeter must never be connected without a filter, see section 07.
Technical specifications
| POWER & LOAD | |
|---|---|
| Rated power (RMS) | 150 W |
| Peak power (MAX) | 300 W |
| Rated impedance | 4 ohm |
| ACOUSTIC | |
| Sensitivity | 110 dB SPL 1W/1M |
| Upper frequency limit | 25 kHz |
| Throat diameter | 25 mm (1") |
| MOTOR & MATERIALS | |
| Voice coil diameter | 32.4 mm / 1.27" |
| Winding material | CCAW (aluminium) |
| Magnet | 8 Oz |
| DIMENSIONS | |
| Overall diameter | 95 mm (3.7") |
| Depth | 47 mm (1.8") |
| Net weight | 0.5 kg |
| Sold as | Pair (2 pieces) |
MANUFACTURER’S LABORATORY DATA · PEAK OR “BURST” FIGURES USED IN SOME MARKETS ARE NOT RMS AND ARE NOT LISTED
Complete the system
Before you install it
- Never connect a tweeter without a filter. A crossover, or at the very least a capacitor in series: full range straight from the amplifier will destroy the voice coil in seconds. This is not optional.
- Cross it high and check the manual. A horn tweeter is meant for the top of the band only. Use the minimum crossover frequency printed in the factory sheet and never go below it — and if you are not sure, write to us before you power it up.
- Keep 4 ohm per channel. Two tweeters in parallel on one channel give 2 ohm: most amplifiers heat up or go into protection.
- 110 dB means you need less gain, not more. A bullet this efficient will be louder than the rest of the system: attenuate it, aim it slightly off-axis, and stop before the amplifier clips. Clipping kills tweeters, power rarely does.
Questions installers ask
spaudio@spaudio.it · +39 340 807 8778
Accepted payment methods
Visa · Mastercard · Maestro · American Express · PayPal · Apple Pay · Google Pay · Shop Pay · Klarna
SP Audio — Super Power Audio. Designed in Italy by Audiocar Import & Export SRLS, Milano, official SP Audio distributor for Europe.