SP-DRIVER 39 / 80W RMS (UNIT PRICE)

قیمت فروش€33,00 قیمت معمولی€66,00
ذخیره €33,00
✅
ReadyShips in 24/48 h from Italy

Pay in easy, interest-free installments with Klarna.


SP Audio - Super Power AudioSUPER POWER AUDIO
DESIGNED IN ITALY
MMXXVI
compression driver · horn included · 105 dB · single unit

80 watt RMS.
Horn already on it.

The compact one of the range: a compression driver sold complete with its ABS+PC horn, 105 dB sensitivity, a 34.4 mm voice coil on an ABS diaphragm, a 34.4 mm throat and 80 W RMS at 8 ohm nominal. Usable range 1.5 kHz – 20 kHz. The price on this page is for one piece.

SP-DRIVER 39 compression driver with ABS+PC horn: 34.4 mm throat, 34.4 mm voice coil, 80 W RMS
80WRMS · 8 Ω
160WMAX · PEAK
105dBSPL 1W/1M
🔒 Secure checkout · SSL & PCI DSS↩ 14 days to change your mind (EU)✓ Invoice from an Italian company✓ Data from the 2026 factory manual
✓ ITALIAN DESIGN✓ 8 OHM✓ HORN INCLUDED✓ UNIT PRICE✓ FREE SUPPORT
01

Power, measured not promised

RMS · 8 Ω
80 W
MAX · PEAK
160 W

PER DRIVER · RMS IS CONTINUOUS POWER, NOT BURST · NOMINAL 8 Ω

02

Why this driver

105 dB: efficiency does the work

A compression driver turns a few watts into a lot of pressure. At 105 dB SPL 1W/1M it stays on top of the midranges and the subwoofer without asking much of the amplifier.

ABS diaphragm on a 34.4 mm voice coil

The moving part is an ABS diaphragm driven by a 34.4 mm coil, wound in two layers of CCAW on a Kapton former. Note: the factory sheet gives ABS, not titanium — the sheet is what counts.

The horn is included

You are not buying a bare motor: this unit ships with its ABS+PC horn already fitted. Nothing else to buy to make it play.

127 mm and 0.968 kg

The smallest of the four SP-DRIVER units: 127 mm overall, 116 mm deep, under a kilo, with a ferrite magnet 90 × 45 × 15 mm and 1.40 T of flux density.

“Continuous RMS only. No peak, no burst, no marketing watts.”
03

Look at it closely

01 · the diaphragm and the throat

ABS diaphragm, 34.4 mm voice coil, 34.4 mm throat. Everything the driver produces passes through that throat before it enters the horn.

02 · the magnet and the body

Ferrite ring 90 × 45 × 15 mm, 1.40 T in a 4.5 mm gap, T-yoke 4.5 mm. Overall 127 mm, 116 mm deep, 0.968 kg.

Free shippingDispatched from Italy in 24–48 working hoursWarranty on manufacturing defectsFree technical support from Italy
FACTORY MANUAL & SPECIFICATION SHEET

Full specifications and mounting data, straight from the 2026 factory sheet.

⇩  Open the manual (PDF)

English · 2026 · opens in a new tab

04

What you receive

One driver, horn included.

The price on this page is for one piece, not a pair. The driver arrives with its ABS+PC horn already mounted, ready to bolt to the baffle. Packed in the SP Audio box; the factory carton holds 2 pieces.

In the box: 1 × SP-DRIVER 39 compression driver with its ABS+PC horn · SP Audio packaging.
Not included: crossover, capacitors, speaker cable and mounting hardware — installation material, chosen for your car.

05

Technical specifications

POWER & LOAD
Rated power (RMS) 80 W
Peak power (MAX) 160 W
Nominal impedance 8 ohm
DC resistance (Re) 5.6 ohm
ACOUSTIC
Sensitivity 105 dB SPL 1W/1M
Frequency range (-10 dB max) 1.5 kHz – 20 kHz
Resonance frequency 1500 Hz
Throat diameter 34.4 mm
Horn material ABS+PC
MOTOR & MATERIALS
Voice coil diameter 34.4 mm
Diaphragm material ABS
Former material Kapton
Winding material CCAW, 2 layers
Winding depth 2.0 mm
Magnet material Ferrite ring
Magnet size 90 × 45 × 15 mm
Flux density 1.40 T
Magnetic gap depth 4.5 mm
T-yoke depth 4.5 mm
DIMENSIONS & PACKAGING
Overall diameter 127 mm
Bolt circle diameter 105 mm
Baffle cutout diameter 85 mm
Depth 116 mm
Flange and gasket 4.5 mm
Net weight 0.968 kg
Factory carton (2 pcs) 28 × 28 × 13 cm
Sold as Single unit (1 piece)

MANUFACTURER’S LABORATORY DATA · PEAK OR “BURST” FIGURES USED IN SOME MARKETS ARE NOT RMS AND ARE NOT LISTED

06

Complete the system

07

Before you install it

  • It always needs a crossover. Never full range. A compression driver must never see the whole signal: run full range, the ABS diaphragm is gone in seconds. A high-pass filter, always.
  • Do not cross it below 1500 Hz. 1500 Hz is the resonance frequency declared by the factory and the bottom of its usable range (1.5 kHz – 20 kHz). Going lower is the quickest way to break it.
  • 8 ohm nominal, 5.6 ohm DC. Check what your amplifier does on 8 ohm before wiring several drivers in parallel on one channel.
  • Aim it, and start with the gain low. A horn is directional: point it at the listener, then bring the level up slowly. Clipping kills drivers far more often than power does.
08

Questions installers ask

How much power does the SP-DRIVER 39 handle?80 W RMS continuous and 160 W peak, at 8 ohm nominal. The price on this page is for one piece.
Is the horn included?Yes. It ships with its ABS+PC horn already fitted — nothing else to buy.
Do I need a crossover?Yes, always. High-pass only, and never below 1500 Hz. Full range destroys the diaphragm.
How much room does it need?85 mm baffle cutout, 105 mm bolt circle, 127 mm overall and 116 mm of depth.
One or two?One. The price on this page is per piece: order two for a stereo pair.
Free technical support from Italy. Write or call and a person answers, with the real data of the product sheets. Tell us what you want to build — power, crossover points, front stage or SPL wall — and we will help you match it.
spaudio@spaudio.it · +39 340 807 8778

Accepted payment methods
Visa · Mastercard · Maestro · American Express · PayPal · Apple Pay · Google Pay · Shop Pay · Klarna

SP Audio — Super Power Audio. Designed in Italy by Audiocar Import & Export SRLS, Milano, official SP Audio distributor for Europe.