SP-DRIVER 54 / 150W RMS (UNIT PRICE)

قیمت فروش€73,00 قیمت معمولی€146,00
ذخیره €73,00
✅
ReadyShips in 24/48 h from Italy

Pay in easy, interest-free installments with Klarna.


SP Audio - Super Power AudioSUPER POWER AUDIO
DESIGNED IN ITALY
MMXXVI
compression driver · horn included · 109 dB · single unit

150 watt RMS.
Horn already on it.

A compression driver sold complete with its ABS+PC horn: 109 dB sensitivity, a 51.6 mm voice coil on a titanium diaphragm, a 25.4 mm (1") throat and 150 W RMS at 8 ohm nominal. Usable range 600 Hz – 20 kHz. The price on this page is for one piece.

SP-DRIVER 54 compression driver with ABS+PC horn: 25.4 mm (1") throat, 51.6 mm voice coil, 150 W RMS
150WRMS · 8 Ω
300WMAX · PEAK
109dBSPL 1W/1M
🔒 Secure checkout · SSL & PCI DSS↩ 14 days to change your mind (EU)✓ Invoice from an Italian company✓ Data from the 2026 factory manual
✓ ITALIAN DESIGN✓ 8 OHM✓ HORN INCLUDED✓ UNIT PRICE✓ FREE SUPPORT
01

Power, measured not promised

RMS · 8 Ω
150 W
MAX · PEAK
300 W

PER DRIVER · RMS IS CONTINUOUS POWER, NOT BURST · NOMINAL 8 Ω

02

Why this driver

109 dB: efficiency does the work

A compression driver turns a few watts into a lot of pressure. At 109 dB SPL 1W/1M it stays on top of the midranges and the subwoofer without asking much of the amplifier.

Titanium diaphragm on a 51.6 mm voice coil

The moving part is a titanium diaphragm driven by a 51.6 mm coil, wound in two layers of CCAW on a Kapton former. That is what keeps the top end clean at high level.

The horn is included

You are not buying a bare motor: this unit ships with its ABS+PC horn already fitted. Nothing else to buy to make it play.

Ferrite motor, 1.90 T in the gap

A ferrite ring magnet ⌀135 × ⌀70 × 17 mm, 1.90 T of flux density and a 7 mm magnetic gap. It weighs 2.79 kg — mass is what keeps a driver stable when it gets hot.

“Continuous RMS only. No peak, no burst, no marketing watts.”
03

Look at it closely

01 · the diaphragm and the throat

Titanium diaphragm, 51.6 mm voice coil, 25.4 mm (1") throat. Everything the driver produces passes through that throat before it enters the horn.

02 · the magnet and the body

Ferrite ring ⌀135 × ⌀70 × 17 mm, 1.90 T in a 7 mm gap, T-yoke 8 mm. Overall 180 mm, 160 mm deep, 2.79 kg.

Free shippingDispatched from Italy in 24–48 working hoursWarranty on manufacturing defectsFree technical support from Italy
FACTORY MANUAL & SPECIFICATION SHEET

Full specifications and mounting data, straight from the 2026 factory sheet.

⇩  Open the manual (PDF)

English · 2026 · opens in a new tab

04

What you receive

One driver, horn included.

The price on this page is for one piece, not a pair. The driver arrives with its ABS+PC horn already mounted, ready to bolt to the baffle. Packed in the SP Audio box; the factory carton holds 2 pieces.

In the box: 1 × SP-DRIVER 54 compression driver with its ABS+PC horn · SP Audio packaging.
Not included: crossover, capacitors, speaker cable and mounting hardware — installation material, chosen for your car.

05

Technical specifications

POWER & LOAD
Rated power (RMS) 150 W
Peak power (MAX) 300 W
Nominal impedance 8 ohm
DC resistance (Re) 6.2 ohm
ACOUSTIC
Sensitivity 109 dB SPL 1W/1M
Frequency range (-10 dB max) 600 Hz – 20 kHz
Resonance frequency 600 Hz
Throat diameter 25.4 mm (1")
Horn material ABS+PC
MOTOR & MATERIALS
Voice coil diameter 51.6 mm
Diaphragm material Titanium
Former material Kapton
Winding material CCAW, 2 layers
Winding depth 2.4 mm
Magnet material Ferrite ring
Magnet size ⌀135 × ⌀70 × 17 mm
Flux density 1.90 T
Magnetic gap depth 7 mm
T-yoke depth 8 mm
DIMENSIONS & PACKAGING
Overall diameter 180 mm
Bolt circle diameter 158 mm
Baffle cutout diameter 132 mm
Depth 160 mm
Flange and gasket 7.6 mm
Net weight 2.79 kg
Factory carton (2 pcs) 38 × 38 × 19 cm
Sold as Single unit (1 piece)

MANUFACTURER’S LABORATORY DATA · PEAK OR “BURST” FIGURES USED IN SOME MARKETS ARE NOT RMS AND ARE NOT LISTED

06

Complete the system

07

Before you install it

  • It always needs a crossover. Never full range. A compression driver must never see the whole signal: run full range, the titanium diaphragm is gone in seconds. A high-pass filter, always.
  • Do not cross it below 600 Hz. 600 Hz is the resonance frequency declared by the factory and the bottom of its usable range (600 Hz – 20 kHz). Going lower is the quickest way to break it.
  • 8 ohm nominal, 6.2 ohm DC. Check what your amplifier does on 8 ohm before wiring several drivers in parallel on one channel.
  • Aim it, and start with the gain low. A horn is directional: point it at the listener, then bring the level up slowly. Clipping kills drivers far more often than power does.
08

Questions installers ask

How much power does the SP-DRIVER 54 handle?150 W RMS continuous and 300 W peak, at 8 ohm nominal. The price on this page is for one piece.
Is the horn included?Yes. It ships with its ABS+PC horn already fitted — nothing else to buy.
Do I need a crossover?Yes, always. High-pass only, and never below 600 Hz. Full range destroys the diaphragm.
How much room does it need?132 mm baffle cutout, 158 mm bolt circle, 180 mm overall and 160 mm of depth.
One or two?One. The price on this page is per piece: order two for a stereo pair.
Free technical support from Italy. Write or call and a person answers, with the real data of the product sheets. Tell us what you want to build — power, crossover points, front stage or SPL wall — and we will help you match it.
spaudio@spaudio.it · +39 340 807 8778

Accepted payment methods
Visa · Mastercard · Maestro · American Express · PayPal · Apple Pay · Google Pay · Shop Pay · Klarna

SP Audio — Super Power Audio. Designed in Italy by Audiocar Import & Export SRLS, Milano, official SP Audio distributor for Europe.